Chevrolet Forum - Chevy Enthusiasts Forums - Search Results

Notices
 
Search: Posts Made By: LCAC_Man
Showing results 1 to 25 of 90
Search took 0.01 seconds.
April 11th, 2019, 1:39 PM
Replies: 4
Views: 716
Posted By LCAC_Man

Look at the WeldTech Designs coil spacer/spindle...

Look at the WeldTech Designs coil spacer/spindle lifts. It takes a fair amount of lift and proper wheel offset to pull off 34's without rubbing hard.
February 25th, 2019, 6:43 AM
Replies: 25
Views: 4,023
Posted By LCAC_Man

you could swap coil packs between the cylinders...

you could swap coil packs between the cylinders as well...it's not typical to fail more than one at a time but it isn't difficult to do..
February 24th, 2019, 4:34 PM
Replies: 25
Views: 4,023
Posted By LCAC_Man

A bad intake gasket wouldn't cause any change to...

A bad intake gasket wouldn't cause any change to compression, it is a possible cause for this but typically not on a wide scale (multiple cylinder misfire) it usually occurs on a single (maybe two...
February 11th, 2019, 10:28 AM
Replies: 12
Views: 1,131
Posted By LCAC_Man

9.5" semi-float 14bolt would require full...

9.5" semi-float 14bolt would require full disassembly for pinion bearing replacement, I think your mechanic is short on labor. If you have 17yrs and 157k miles on original u-joints and center...
February 11th, 2019, 6:54 AM
Replies: 12
Views: 1,131
Posted By LCAC_Man

What model express do you have? 1500/2500/3500?...

What model express do you have? 1500/2500/3500? 135 or 155" wheel base? How many miles on it? Do you know what model rear axle you have? If it's a 14bolt AAM/GM Corp then the pinion bearing swap is...
February 9th, 2019, 5:34 PM
Replies: 12
Views: 1,131
Posted By LCAC_Man

center carrier bearing of the driveshaft if it's...

center carrier bearing of the driveshaft if it's a two piece unit
February 9th, 2019, 5:33 PM
Replies: 14
Views: 1,339
Posted By LCAC_Man

It depends on what sections you are replacing,...

It depends on what sections you are replacing, for some you have to lift the body or you'll mangle them..
February 2nd, 2019, 10:03 AM
Replies: 53
Views: 5,739
Posted By LCAC_Man

if you really believe you have a module issue you...

if you really believe you have a module issue you need to borrow a GM MDI / GDS tech tool, it will allow you to determine/test the health of each system. Your van is too new to use the older Tech2...
February 1st, 2019, 8:31 AM
Replies: 53
Views: 5,739
Posted By LCAC_Man

I agree, my bet is this will be a power...

I agree, my bet is this will be a power distribution issue, the computers protect themselves when they see low voltage/poor ground. If you want to look at anything go to the bcm battery voltage input...
January 20th, 2019, 1:55 PM
Replies: 53
Views: 5,739
Posted By LCAC_Man

loss of communicaton codes are common when...

loss of communicaton codes are common when voltage drops below about 10.5vdc, if you can plug in a scan tool and get/clear codes your data bus is working fine
January 18th, 2019, 8:44 AM
Replies: 24
Views: 2,052
Posted By LCAC_Man

Glad to hear you got it done!

Glad to hear you got it done!
January 18th, 2019, 7:06 AM
Replies: 24
Views: 2,052
Posted By LCAC_Man

https://cimg4.ibsrv.net/gimg/chevroletforum.com-vb...

https://cimg4.ibsrv.net/gimg/chevroletforum.com-vbulletin/1156x888/backup_lamp_circuit_5ed2d6ae2dd29a239571f2ce8d08b3825889b1a5.png
Well..."someone" doesn't know wtf they are talking about and...
January 17th, 2019, 4:47 PM
Replies: 24
Views: 2,052
Posted By LCAC_Man

it's right on the drawing guys... Connector...

it's right on the drawing guys...
Connector C318 pin D3, light green is the correct positive reverse circuit. The C318 connector is behind the drivers kick panel usually tucked behind the connector...
January 15th, 2019, 7:03 AM
Replies: 19
Views: 2,141
Posted By LCAC_Man

on a different subject...are you happy with the...

on a different subject...are you happy with the aluminess steps? did you do the install yourself?
January 14th, 2019, 1:36 PM
Replies: 53
Views: 5,739
Posted By LCAC_Man

seized/shorted starter, loose cable connection at...

seized/shorted starter, loose cable connection at the starter, bad battery ground connection at the motor/frame
January 11th, 2019, 10:33 AM
Replies: 15
Views: 1,228
Posted By LCAC_Man

or perhaps it's like the teacher telling the...

or perhaps it's like the teacher telling the bully to shut up (and of course he doesn't, because he's "right"); then expelling him from class so that the rest of the students can learn..
January 11th, 2019, 7:36 AM
Replies: 26
Views: 3,474
Posted By LCAC_Man

Given that you want to haul both people and gear...

Given that you want to haul both people and gear and want to tow I'd only consider an 03 or later 3500 (be sure it has a full floater rear axle) with 6.0 LS based motor, if you look at 97-02's only...
January 10th, 2019, 10:46 AM
Replies: 26
Views: 3,474
Posted By LCAC_Man

As mentioned above, tow package is an easy DIY...

As mentioned above, tow package is an easy DIY project.
Hightops are both more expensive and harder to find. You'll have to be more patient and willing to travel to get a good one.
$10k won't be...
January 8th, 2019, 11:00 AM
Replies: 26
Views: 3,474
Posted By LCAC_Man

getting a hightop extended van and putting your...

getting a hightop extended van and putting your bunk over the seats would probably be the best solution for you
January 6th, 2019, 10:03 AM
Replies: 28
Views: 1,559
Posted By LCAC_Man

probably a cold solder joint on a return for the...

probably a cold solder joint on a return for the coils, they would likely be tied together.
January 6th, 2019, 7:52 AM
Replies: 28
Views: 1,559
Posted By LCAC_Man

I think it's two for the trailer option, two for...

I think it's two for the trailer option, two for turn signals and two for hazards...I'd have to look at the schematic again to confirm. Glad you found your problem!
December 18th, 2018, 8:28 AM
Replies: 25
Views: 3,354
Posted By LCAC_Man

it will be a tow rig for my rockcrawler (see a...

it will be a tow rig for my rockcrawler (see a bit of it in the back of the pic above) and as a rough terrain camper. I'll start the camper phase build out next year
December 16th, 2018, 6:57 PM
Replies: 13
Views: 2,365
Posted By LCAC_Man

you have to manipulate the slider back and forth...

you have to manipulate the slider back and forth a bit (particularly on the driver side) to clear the steering wheel but it's something you figure out quick, you do have to crack the doors open for...
December 16th, 2018, 5:48 PM
Replies: 13
Views: 2,365
Posted By LCAC_Man

https://cimg7.ibsrv.net/gimg/chevroletforum.com-vb...

https://cimg7.ibsrv.net/gimg/chevroletforum.com-vbulletin/1600x1200/h87_409b831f693824fe8389f67b9c247e3f58b68cf9.jpg...
December 16th, 2018, 5:38 PM
Replies: 25
Views: 3,354
Posted By LCAC_Man

https://cimg5.ibsrv.net/gimg/chevroletforum.com-vb...

https://cimg5.ibsrv.net/gimg/chevroletforum.com-vbulletin/1600x1200/j14_2d373c5df504583f4b73af26ae1b73c6fa7181c6.jpg...
Showing results 1 to 25 of 90
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.