Since I'm bored, I'll share my latest install, a phone mount, Aukey 360 degree phone mount. Works pretty good, and happy with the location.
https://cimg3.ibsrv.net/gimg/chevrol...683ae27cfb.jpg good spot, will upload pic of torque pro app shortly Also, I installed 7 inch curtain holders from lowes, cannot believe they made open trays without a lip to hold things in. https://cimg3.ibsrv.net/gimg/chevrol...6deb59dd53.jpg spring curtain rods, couple bucks from lowes |
Torque pro works great on my 2019, I was mainly interested in transmission temperature, but a tachometer and some other gauges was a good idea. I don't think the ambient temp works correctly, not sure where it reads from, but its mostly wrong.
https://cimg5.ibsrv.net/gimg/chevrol...228b46c7ad.jpg torque pro on a huawei p30 pro |
I'm surprised the suction cup sticks to the textures dash.
|
Originally Posted by mountainmanjoe
(Post 462570)
I'm surprised the suction cup sticks to the textures dash.
|
Not exactly today, last week after work Friday night/Saturday morning the starter locked up at the gas station. Fixed with a junk yard swap from a Saturday afternoon.
Sunday finally got my engine console block done weekly planners |
During the week I cut a carpet for the back of the 94 and today I cut up some 1/8th plywood to form interior panels plus a couple of old sliding closet doors (cost: free) to make a shelf and divider in the back. I need to cut plywood sheet #3 to make part of the headliner and the rest will finish off the left side interior panel. It will need a 4th sheet to finish the headliner. The G-van top is about 58-59 inches across, just shy of 5 feet. From the back of the B-post to the rear is about 10 1/2 feet.
This has a rear heat/AC unit and a return hose comes off the bottom straight down and runs into the side of the van. If GM had made this outlet turn 90' so it's parallel to the ground it would be much easier to run. I spent an hour last night looking at van photos and found even fancy high end conversions with this unit in them, that hose is visible coming off the unit and running into the interior paneling. A neighbor curbed those doors and back in the day my grandfather made a basement bar top out of a similar hollow core door so I thought maybe I could use them and get a little vintage look going. Being older they have a fairly decent filler in them and I can go back and slip some wood in the cut ends. Next up is a platform over the wheel houses to serve as a bed which will also get a carpet over it. The lower 18 inches of the side panels will get some too. The remnant was about twice as big as I needed to do the rear of the van so plenty left over for the side panels, for lower door panels, etc. It looks pretty nice inside already. I am just glad to get rid of the work shelves and stuff that came in it though. They rattled and banged and made a ton of noise, they were just kind of cobbed in with not nearly the number of bolts they probably should have had. Sold them for $800 though so all good there. |
Finally finished completed ONE parking brake pad replacement. Much cussing was involved.
I did this without removing the axles and got the impression that the main spring could be pushed in place once mounted. Nope, not so for the pad set I bought. Next, the other side...upside down. Grrr, I hate drum brakes. :mad: |
Parking brake pads shouldn't really wear out, should they? If they're applied while parked?
|
Originally Posted by mountainmanjoe
(Post 468769)
Parking brake pads shouldn't really wear out, should they? If they're applied while parked?
This year's mess started simple: Flush the brake fluid. Oops, bleed screws where rusted crazy, only able to remove one out of four. Considered drilling out, but the calipers were rusty mess anyway and who knew what else was in there? How much work to cleanup? Decided to go for new calipers on all four, new rotors up front (replace the rears last year). Oops, parking pads, etc. Finally done, installed all new brackets/calipers. Time for cables. Oops, front brake cables okay, rear too rusted to seal. GAH! :mad: New cables ordered. Removed old cables. Oops, one of the brakes lines was rusted into the compress nut at the cable. &(*)&)&#)%!!! :mad: Working on a line patch. So much fun. :D |
All times are GMT -5. The time now is 9:18 AM. |
© 2024 MH Sub I, LLC dba Internet Brands