|
Yep, I just reset the password and logged in at socaliguy81. I didn't notice any bans placed on the account. I sent you a PM.
|
2010 tahoe pin 0 is pin 6?top left plug !
Originally Posted by socaliguy81
(Post 91647)
Well, after a lot of searching for the Bose Nav/DVD/Rear Ent wiring diagram, I finally found the only useable signal for adding a sub amp. The issue I had was that tapping the speaker wires on the Bose system changed the impedence too much and threw the Bose amp into a state of confusion. The only logical reasoning behind this is that Bose uses an auto-clip-sensning system that basically tells the amp how much stress the speaker is under through the language of impedence. Notice how when you rotate your volume knob all the way up, it just magically knows when to stop? I realized also that adding an amp for mids and highs would have to be done by grabbing the low level signal before the Bose amp FYI.
Attachment 15201 The center console subwoofer is practically located under the dash. After learning that the Bose amp was in the center console at the rear under the storage area, I figured there must be high level sub signal traveling through the center console. Attachment 15202 Attachment 15203 Sure enough, I popped out the very easily accessible storage tray and spied a 4-wire harness. You might be thinking only 1 pair of wires go to a sub. Well, as I learned when adding an amp to my CTS w/ Bose, they like to run 2 pairs, one for each voice coil. All you have to do is tap each pair and run to a line-level adapter or hi-lo converter as some of you know them by. The wiring is as follows: ***These colors are on the amp side of the plug. The sub side has different colors all together.*** Voice Coil #1 aka Channel 1 +Dark Blue w/ White Stripe - Light Green w/ Black Stripe Voice Coil #2 aka Channel 2 +Dark Green -Light Blue w/ Black Stripe ***THESE ARE SUB LEVELS NOT FULL RANGE..TAPPING THESE WIRES ARE ONLY FOR INSTALLING SUBS*** **Since it is easier to tap the larger gauge wires on the sub side of the harness, just use the plug's corresponding letters (ABCD) to match the wires up.** Attachment 15204 There is plenty of room under most second row seating for one large amp or multiple smaller amps. Even the factory beauty board can be cut to easily flush amps in and hide wiring. Attachment 15205 Attachment 15206 The 12Volt Main and 12Volt Accessory/Ignition wire locations are pictured below. Attachment 15207 Attachment 15208 Attachment 15209 https://img.photobucket.com/albums/v...e/P4130015.jpg Attachment 15210 Attachment 15211 Attachment 15212 I am a professional installer who works out of Southern California and would love to help out if anyone needs. 760-773-8728 Travis Brown "socaliguy81@yahoo.com" |
Originally Posted by Cruz H
(Post 243624)
I got a 2008 tahoe i want to know what are the speakers colorcodes from the bose amp because i want to run wires from the center speaker wires to my new amp
|
|
Originally Posted by Jarvis Handy
(Post 430854)
Did you ever find out what colors went to what wires
|
Originally Posted by Cruester
(Post 430856)
U will need a high to low converter to run to ur amp ,I have a 2010 tahoe and used a high to low to my amp after wiring it from before the amp wires in center console!works great!
|
Originally Posted by Cruester
(Post 430856)
U will need a high to low converter to run to ur amp ,I have a 2010 tahoe and used a high to low to my amp after wiring it from before the amp wires in center console!works great!
|
Originally Posted by Cruester
(Post 430859)
If u have further questions hit me up on messanger!marlin goulet!
Then i hooked up the respective wires to the wires on the amp. What i know so far is From the amp [ ] Dark Blue white stripe - postive [ ] Light green/black -negative [ ] Dark Green - postive [ ] Light blue/black - negative It still won't turn on. Amp wont even turn on Now when i ran the converter to the rear speakers everything worked fine. Just lookes messy Any tips!?!?! |
Originally Posted by Cruester
(Post 430859)
If u have further questions hit me up on messanger!marlin goulet!
|
Originally Posted by Cruester
(Post 430861)
Gotta run the amp turn on wire under the dash by the brake pedal is a black cover,theres a spot in there to run the turn on to!
|
| All times are GMT -5. The time now is 2:55 PM. |
© 2024 MH Sub I, LLC dba Internet Brands